Practice HPE6-A85 Exam Online

Question 1

What happens when the signal from an AP weakens by being absorbed as it moves through an object?

A : APs will use bonded channels to decrease latency to clients

B : Signal to Noise Ratio (SNR) increases

C : Signal to Noise Ratio (SNR) decreases

D : Aruba Central dynamically moves clients to neighboring APs

Answer: C

Question 2

A hospital uses a lot of mobile equipment for the diagnosis and documentation of patient data What Is the ideal access switch for this large hospital with distribution racks of over 400 ports in a single VSF stack?

A : CX 6300

B : OCX 6400

C : OCX 6200

D : OCX 6100

Answer: A

Question 3

You are configuring a network with a stacked pair of 6300M switches used for distribution and layer 3 services. You create a new VLAN for users that will be used on multiple access stacks of CX6200 switches connected downstream of the distribution stack You will be creating multiple VLANs/subnets similar to this will be utilized in multiple access stacks What is the correct way to configure the routable interface for the subnet to be associated with this VLAN?

A : Create a physically routed interface in the subnet on the 6300M stack for each downstream switch.

B : Create an SVl in the subnet on each downstream switch

C : Create an SVl in the subnet on the 6300M stack, and assign the management address of each downstream switch stack to a different IP address in the same subnet

D : Create an SVl in the subnet on the 6300M stack.

Answer: D

Question 4

You have been asked to onboard a new Aruba 6300M in a customer deployment You are working remotely rather than on-site You have a colleague installing the switch The colleague has provided you with a remote console session to configure the edge switch You have been asked to configure a link aggregation going back to the cores using interfaces 1/1/51 and 1/1/52 The Senior Engineer of the project has asked you to configure the switch and 1Q uplink with these guidelines 1. Add VLAN 20 to the local VLAN database with name Mgmt 2. Add L3 SVl on VLAN 20 for Management using address 10 in the 10.1.1 0/24 subnet 3. Add LAG 1 using LACP mode active for the uplink 4 use vlan 20 as the native vlan on the LAG 5. Make sure the interfaces are all ON. Which configuration script will achieve the task?

A : Edge1# conf t vlan 20 name Mgmt interface vlan 20 ip address 10.1.1.10/24 no shut interface lag 1 shut vlan access 20 lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut

B : Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1.1 10/24 no shut interface 1/1/51.1/1/52 shut vlan trunk native 20 vlan trunk allowed all lag 1 lacp mode active interface 1/1/51.1/1/52 no shut

C : Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1 1 10/24 no shut interface lag 1 shut vlan trunk native 20 vlan trunk allowed all lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut interface 1/1/51.1/1/52 no shut

D : conf t vlan 20 name Mgmt ip address 10 1 1.10/24 no shut interface lag 1 shut vlan trunk native 1 vlan trunk allowed all lacp mode active int 1/1/51.1/1/52 shut no routing interface lag 1 no shut interface 1/1/51.1/1/52 no shut

Answer: C

Name:	Aruba Certified Campus Access Associate
Exam Code:	HPE6-A85
Certification:	HPE Aruba Certified
Vendor:	HP
Total Questions:	60
Last Updated:	Apr 25, 2024

HP HPE6-A85